ASTM D1204 PDF
This standard is issued under the fixed designation D ; the number relevant ASTM material specification shall take precedence. GeoTesting Express is a provider of Geosynthetic Testing Services – ASTM D,Standard Test Method for Linear Dimensional Changes of Non-rigid. ASTM D Standard Test Method for Linear Dimensional Changes of Nonrigid Thermoplastic Sheeting or Film at Elevated Temperature.
|Published (Last):||8 January 2018|
|PDF File Size:||13.39 Mb|
|ePub File Size:||12.53 Mb|
|Price:||Free* [*Free Regsitration Required]|
Dimensional Stability ASTM D1204
Enabling you to identify and mitigate the intrinsic risk in your operations, supply chains and business processes. The midpoint adtm each edge shall be marked for use as a reference point when? If you feel that your comments have not received a fair hearing you should make your views known to the ASTM Committee on Standards, at the address shown below.
A negative value denotes shrinkage, and a positive value indicates expansion.
Dimensional Stability ASTM D
Assurance Testing Inspection Certification. The distances between the reference marks are re-measured and recorded. Need help or have a question? A number in parentheses indicates the year of last reapproval.
Active Risk Management
Your comments are invited either for revision of this standard or for additional standards and should be addressed to ASTM International Headquarters. Each specimen shall be marked to show the direction of calendering or extrusion. Talc dusted paper is inserted to form a sandwich around the specimen. Auditing Consulting Sourcing Training. Points a, b and x, y are reference marks at midpoint of test specimen edges. Originally approved in Testlopedia – The Plastics Testing Encyclopedia.
Precision and Bias If there are no relevant ASTM material speci? November 1, 1 Revised Section 7 and 8. Percent linear change is equal to final length minus original length divided by original length multiplied by Validating the specifications, value and safety of your raw materials, products and assets. NOTE 2—The paper should be well dusted, and the specimens should not be restricted either by the paper or the clips.
Last previous edition approved in as D – Shorter reconditioning times may be used if it can be shown that equivalent results are obtained. The test gives an indication of lot-to-lot uniformity with regards to internal stress introduced during processing.
Standards can be obtained from appropriate standards authorities. Sandwiches must not be stacked, as this may restrict movement of the plastic between the papers. Dimensional Stability is a measurement of the linear dimensional change resulting from exposure to temperature. Send us a request Wilton UK: Any test specimen preparation, conditioning, dimensions, or testing parameters, or combination thereof, covered in the relevant ASTM material speci?
It is imperative that the specimens be free to change shape as strains are relieved during the period of test. This standard has been approved for use by agencies of the Department of Defense. Table 1 of Classi? The sandwiched specimens are placed in an oven for a specified amount of time.
Evaluating how your products and services meet and exceed quality, safety, sustainability and performance standards.
ASTM D 尺寸变化率_百度文库
Individual reprints single or multiple copies of this standard may be obtained by contacting ASTM at the above address or at phonefaxor service astm. ASTM D – It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
Global Reach Intertek is the industry leader with over 42, people in 1, locations in over countries. Formally confirming that your products and services meet all trusted external and internal standards. Send us a request Need help or have a question? Inspection Validating the specifications, value and safety of your raw materials, products and assets.
Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend.
ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentioned in this standard.
Fasten the papers together with paper clips. Remove the astj and measure the distance between the opposite edges of the specimens at the reference marks to the nearest 0. Testing Evaluating xstm your products and services meet and exceed quality, safety, sustainability and performance standards. Current edition approved Nov. The test gives an indication of lot-to-lot uniformity as regards to the degree of internal strains introduced during processing. The test is mostly used for sheeting or film made by extrusion or calendar processes.
This standard is subject to revision at any time by the responsible technical committee and must be reviewed every? Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own adtm. The dimensions of the specimen are taken at reference marks. Whether your business is local or global, we can ensure your products meet quality, health, environmental, safety, and social accountability standards for virtually any market around the world.
NOTE 1—This test method and ISO address the same matter, but differ in technical content and results cannot be directly compared between the two methods.
After removal from the oven, the specimens are reconditioned at room temperature for a minimum of one hour. Certification Formally confirming that your products and services meet all trusted external and internal standards.
Through our network of over 43, people in 1, laboratories and offices in countries, Intertek provides aztm and safety solutions to a wide range of industries wstm the world.