FREQROL E500 MANUAL PDF
View and Download Mitsubishi Electric FR-E instruction manual online. FR- E Inverter pdf Inverter Mitsubishi Electric Freqrol-A Instruction Manual. Part No: FR-ESK-EC, Brand: Mitsubishi, Model: E Series – kW V Download the Mitsubishi E Manual and Installation Guide from the links. changes both to this manual and to the specifications and design of the hardware at any . struction Manual of the frequency inverter FR-E This Installation.
|Published (Last):||15 November 2017|
|PDF File Size:||2.22 Mb|
|ePub File Size:||18.29 Mb|
|Price:||Free* [*Free Regsitration Required]|
By pressing ‘print’ button you will print only current page.
Instruction Manual Fr-e500 Mitsubishi FREQROL Inverters
Regenerative Brake Duty pr. T L Remove jumpers. Fr-esc to sc-ene; fr-essc to sc-ene 38 pages. Offline Auto Tuning Function pr.
Connect and operate the option unit carefully in accordance with the corresponding option unit manual. About The Control Panel 3. Incorrect system configuration and connections can cause the inverter to operate improperly, its life to be reduced considerably, and in the worst case, the inverter to be damaged.
Instruction Manual Fr-e Mitsubishi FREQROL Inverters | eBay
Page – Remote setting function selection Pr. PID reverse action selection For cooling, etc. When the control panel is used, the same value as manuual the PU is only displayed: The calibration values are not initialized.
Ensure that the cables are connected to the correct terminals. Refer to the following list and prepare appropriate peripheral devices: Page – Reverse rotation prevention selection P If a ground fault occurs during operation, the protective function is not activated. Do not use an earth leakage circuit breaker as an electric shock protector without connecting the equipment to the earth.
Output Terminal Function Selection pr. When entering 0 to 10VDC, always make this setting. Always read the instructions before using the equipment 6. Dc Dynamic Brake pr. Cable conforming to EIA e. Load Pattern Selection pr.
MITSUBISHI ELECTRIC FR-E INSTRUCTION MANUAL Pdf Download.
It can not be measured accurately with a meter or general instrumentation. Prepare required instruments and parts according to the operation mode.
Use any of Pr.
These settings differ in starting method. Parameter Name Application Number Maximum frequency Used to set the maximum and minimum output mmanual. Page 5 2 Wiring CAUTION Do not fit capacitive equipment such as a power factor correction capacitor, radio noise filter or surge suppressor to the output of the inverter.
Page – Troubleshooting Page – Speed greatly differs from the setting Page – Operation mode is not changed properly Page – Precautions for Maintenance and Inspecti E00 Rotation Prevention Selection pr.
When there is a commercial power supply-inverter switch-over circuit as shown below, the inverter will be damaged by leakage current from the power supply due to arcs generated at the time of switch-over or chattering caused by a sequence error.
Got it, continue to print. Enter the 4 to 20mADC process value signal Process value input from the detector. Operation mode can be switched to PU operation mode. Check point Find the cause of alarm feeqrol. Page 71 1 Alarm history Four past alarms can be displayed with the key. Reverse rotation For example 1 Inverter status b3: Inverter running RUN b1: Set value “0” factory setting. Page Page – User group freqrrol Pr.
On receipt of a data error occurrence, the inverter returns “reply data 3” to the computer again. Before using the inverter, please read this manual carefully to use the equipment to its optimum. This may cause a gravity drop when the inverter is used in vertical lift application.
Incorrect handling might cause an unexpected fault. It may also be activated by a surge voltage generated in the power supply system.
Enter text from picture: The following table lists the cables and crimping terminals used with the inputs R L S LT L and outputs U, V, W of the inverter and the torques for tightening the screws: Overload OL monitor rotation When connecting the high power factor converter FR-HC to suppress power harmonics, wire as shown below. Select the type of the no-fuse breaker NFB in response to the power Power factor supply capacity.
Always read the instructions in this chapter before using the equipment.