GRAPHTEC FC8000 MANUAL PDF

Vinyl Cutter Download Graphtec FC, Vinyl Cutter Machine Download Software Installation & Operation Manual in pdf ( MB) > Download Now. Manually Adjusting the FC ARMS Sensor Level for Glossy Media and Glossy Laminated Prints. When using some glossy media or when using glossy. View and Download GRAPHTEC FC Series user manual online. Cutting Pro . FC Series Plotter pdf manual download.

Author: Negami Dajinn
Country: Cambodia
Language: English (Spanish)
Genre: Relationship
Published (Last): 23 May 2018
Pages: 309
PDF File Size: 17.7 Mb
ePub File Size: 7.8 Mb
ISBN: 967-7-24896-808-1
Downloads: 42607
Price: Free* [*Free Regsitration Required]
Uploader: Zulkilmaran

Decrease the value if the media is thin, and increase the value if the media is thick. Maintenance This chapter describes the operation and information regarding maintenance. Steps are different from here depending if it is going to move to registration mark automatically to scan the registration mark, or if it is going to move manually to scan.

It can be set back to enabled from This setting is maintained even if the power is here too. Force of the blade when the cross cut is made is called cross cut force, and it can be adjusted. Adjust the setting value considering the balance. Position of the Origin Point and the Registration Mark The origin point after scanning the registration mark will be as shown below.

ARMS (Advanced Registration Mark Sensing system)

All the operations described in this chapter is to start from the READY status media is set as a general condition. Operation selection menu is displayed on the screen of the control panel while it is stopped. In case of using the Graphtec software, reversed color mark can be easily created.

Setting The Force Setting the Force Set the cutting force that is used in each of the condition numbers. It makes it easier to confirm the cutting results if you perform this operation after the cutting is completed.

  EXPLORACION NEUROLOGICA PDF

GRAPHTEC FC8000 Series User Manual

The tool carriage will start moving, so there is a chance of injury. Press the [2] key TOOL. Page Repeat steps 3 to 5 and select the 4 values to be set. Perform Automatic Pre Feed When Cut Data is Received It is grapthec to feed and reverse the media automatically for specified amount when the plotter receives the cutting data.

Option This chapter describes about the options. Check if the offset value is set correctly by following.

It is possible to increase the precision when cutting outline of the image plotted by other plotter or need to cut the media again by this method, if the registration mark cannot be scanned by the ARMS. Supplement Message to confirm tool position is displayed.

It depends on the media specifed by Graphtec and setting conditions. Such prohibited action is described by an illustration or text within or next to the symbol.

The reply will be when set toand when set to Daily Maintenance 12 – Daily Maintenance Daily Maintenance During the course of daily plotter operation, be sure to observe the following precautions: Self Diagnostic Test 13 – Self Diagnostic Test Operation status can be tested by self diagnostic test by operating the sensors and switches following the instruction on the screen.

Perform Automatic Pre Feed When Media is Set Initial Feed It can be set to automatically feed and return the length of the Supplement page when the media is loaded and the media set lever is raised. Page 9 How to Use Control Panel Confirm the Results of the Cutting Test the cutting test results, and adjust to optimal setting.

It is appropriate for cutting multiple numbers of stickers or similar. Preface In addition to cutting marking film and other media, an FC series plotter can also be used as a pen plotter. Setting Regarding Cutting Quality There are times that ideal cutting may not be possible, such as the lines may shift, corners deform, or uncut sections occur, due to the characteristics of the media thickness, how hard it is, etc.

  EUGEN SANDOW SYSTEM OF PHYSICAL TRAINING PDF

Convenient Functions Chapter 4: Coordinate value displayed here is the distance to the tool carriage from the origin point. Loupe adjusting The Position 14 – Loupe Adjusting the Position Axis Alignment, Cut Area Positioning The loupe bombsight is used to align points for adjustment during axis alignment operations, and to align the corner points when specifying the plotting area. All the tool condition that is received from the computer will be ignored, and only the setting and change of the tool condition from the control panel is accepted when MANUAL is selected.

GRAPHTEC FC SERIES USER MANUAL Pdf Download.

Alignment registration mark A function to continuously cut the print with same design aligned, using a plugin for the Illustrator. The axis alignment using 2-point and 3-point that are faster with limited compensation are also available.

While pushing the tool holder in the upward direction, push the CAUTION tool all the way into the holder until its flange contacts the upper When pushing the tool holder with your fingers, part of the holder. After the media is detected, the plotter is ready to receive data for cutting or plotting.

Be sure to use the basket when cutting long-axis media of more than 1 meter is to be produced.

VPN