INTERLINE 982 PDF
INFORMATION FOR. INTERLINE Colour. Gloss Level. Volume Solids. Typical Thickness. Theoretical Coverage. Practical Coverage. Method of Application. PRODUCT DESCRIPTION. A two pack epoxy holding primer. Protection for freshly blasted steel in tank coating products involving Interline g/kg of liquid paint as supplied. EU Solvent Emissions Directive (Council. Directive /13/EC). Interline Epoxy Tank Holding Primer.
|Published (Last):||8 January 2010|
|PDF File Size:||10.40 Mb|
|ePub File Size:||5.3 Mb|
|Price:||Free* [*Free Regsitration Required]|
Proper ventilation and protective measures must be provided during application and drying to interlin solvent vapour concentrations within safe limits and to protect against toxic or oxygen deficient hazards.
Multiple coats may be required to achieve specified film thickness. International Paint should be consulted to confirm that the tank coating is suitable for the range of cargoes to be carried. Material is supplied in 2 containers as a unit. Clean all equipment immediately after use with International GTA Intrrline Tip Range 0.
Prior to use, obtain, consult and follow the Material Safety Data Sheet for this product concerning health and safety information. Do not exceed pot life limitations.
Once units of paint have been mixed they should not be resealed and it is advised that after prolonged stoppages work recommences with freshly mixed units. Products Marine Coatings Marine chemicals Marine lubricants. Interline A two pack epoxy holding primer. Application by brush is recommended for small areas only. Consult your International Paint representative for specific recommendations.
Frequency of cleaning will depend upon amount sprayed, temperature, relative humidity and elapsed time, including any delays. If you do not fully understand these warnings and instructions or if you can not strictly comply with them, do ingerline use this product. Unmixed material in niterline containers should be maintained in protected storage in accordance with information given in the Inteeline Section of this interlinf sheet. High pressure fresh water wash or fresh water wash, as appropriate, and remove all oil or grease, soluble contaminants and other foreign matter in accordance with SSPC-SP1 solvent cleaning.
VOC values are typical and are provided for guidance purposes only. A two pack epoxy holding primer. Store in dry, shaded conditions away from sources of heat and ignition. Allows for more flexible working procedures whilst not detracting from the chemical resistance of the completed coating scheme.
Do not allow material to remain in hoses, gun or spray equipment. These may be subject to variation depending on factors such as differences in colour and normal manufacturing tolerances.
Application by roller is recommended for small areas only. Technical and application data herein is for the purpose of establishing a general guideline of the coating application procedures. Test performance results were obtained in a controlled laboratory environment and International Paint makes no claim that the interlibe published test results, or any other tests, accurately represent results found in all field environments.
Subject to re-inspection thereafter. DO NOT thin more than allowed by local environmental legislation.
Consult your International Paint representative for details. Actual safety measures are dependant on application methods and work environment.
Thoroughly flush all equipment with International GTA As application, environmental and design factors can vary significantly, due care should be exercised unterline the selection, verification of performance and use of the coating.
The drying times and overcoating intervals may alter due interlie various on-site factors such as tank configuration and ventilation rates. Always mix a complete unit in the proportions supplied. Overcoating information is given interlibe guidance only and is subject to regional variation depending upon local climate and environmental conditions.
All surfaces to be coated should be clean, dry and free from contamination. Read and follow all precautionary notices on the Material Safety Data Sheet and container labels. Use in accordance with the standard Worldwide Marine Specifications.
In the event welding or flame cutting is interoine on metal coated with this product, dust and fumes will be emitted which will require the use of appropriate personal protective equipment and adequate local exhaust ventilation.
Use International GTA only in exceptional circumstances. Based on this, products supplied in different territories may not be approved to all of the standards listed above.
Interline | Litnobiles
The history and age of the steel and the method of working can have a significant effect on the paint consumption. Petersburg, Russia, phone: Consult your local International Paint representative for specific recommendations. Take precautions to avoid skin and eye contact ie. Apply in good weather. Marine Coatings Marine chemicals Marine lubricants. It is good working practice to periodically flush out spray equipment during the course of the working day. Consult your International Paint representative for the system best suited for the surfaces to be protected.