INTERSEAL 670HS PDF
International. Interseal HS – Temperate – North, South and East Europe. Primers / Tie Coats – Epoxy Primer. Find out more. Speak with one of our experts to. Interseal HS is certified to ANSI/NSF standard As a high build epoxy it is suitable for a variety of new construction applications including immersion. INTERSEAL HS – ALUMINIUM – L (). Product Code:INTHS- EGAGL. Product Description: A low VOC, two component high build, high.
|Published (Last):||26 April 2018|
|PDF File Size:||5.24 Mb|
|ePub File Size:||1.57 Mb|
|Price:||Free* [*Free Regsitration Required]|
Brush Typically mils microns can be achieved Roller Typically mils microns can be achieved How to use Mixing Material is supplied in two containers as a unit. However, it can be used over suitably primed surfaces.
Loose or flaking coatings should be removed back to a firm edge. We recommend that Customer first purchases the smallest Product available or access an industry standard colour chart in person and not digitally to ensure that the colour is acceptable for its purposes. However, this product is not recommended where thermoplastic coatings such as chlorinated rubbers and vinyls have previously been used. Coverage intersal quoted are approximate, you agree that coverage depends on the condition of the substrate, surface absorption, texture and application method.
A low VOC, two component high interxeal, high solids surface tolerant epoxy maintenance coating. Avoid using a mixture of application methods whenever possible.
However, this product is not recommended where thermoplastic coatings such as chlorinated rubbers and vinyls have previously been used. Intended Uses For application to a wide variety of substrates including hand prepared rusty steel, abrasive blast cleaned and hydroblasted steel, and a intdrseal range of intact, aged coatings.
International Interseal HS is a low VOC, two component high build, high solids surface tolerant epoxy maintenance coating. Application should then be to jnterseal suitably primed surface.
Sagola or Air texture gun fitted with a mm nozzle. Consult International Protective Coatings for further details.
Mouse over image to zoom. A surface profile of mils microns is recommended. If salt water is used in the wet blast process the resulting surface must be thoroughly washed with fresh water before application of Interseal HS. The figures stated above are approximate. Press and move to zoom. Low or high temperatures may require specific application techniques to achieve maximum film build.
International Interseal HS – Rawlins Paints
Application Brush, Roller, Spray The figures stated above are approximate. Once the unit has been mixed it must be used within the working pot life specified. International Interseal HS is a low VOC, two component high build, high solids surface tolerant epoxy maintenance coating, for application to a wide variety of substrates including hand prepared rusty steel, abrasive blast cleaned and hydroblasted steel, and a wide range of intact, aged coatings. When applying by methods other than airless spray, the required film build is unlikely to be achieved.
Please note that NBS product guidance is not a replacement for the manufacturer’s literature and it is recommended that International Paint Ltd be consulted before specifying. Interseal HS can be used as a non-skid deck system by modification with addition of GMA crushed flint aggregate. Varnish Water base Hybrid.
The minimum purchase order quantity for the product is 1. The surface to be coated should be clean, dry and free from contamination. Consult International Protective Coatings for further details. Where a cosmetically acceptable topcoat is required the following products are recommended:.
International Interseal HS Reference: Application should then be to a suitably primed surface. Avoid using a mixture of application methods whenever possible.
Systems recommendation Interseal HS will normally be applied to correctly prepared steel substrates. Consult International Protective Coatings for alternative recommendations. Typical thicknesses will be between milsmicrons. Trowel or roller can be used for small areas.
Typically this would apply to C or D grade rusting in this standard. Preferred application is by a suitable large tip hopper gun e. Surface iterseal revealed by the blast cleaning process, should be ground, filled, or treated in the appropriate manner. With freshly blasted surfaces a slight degree of flash rusting is allowable, and is preferable to the surface being too wet.