ISO 7816-2 PDF
ISO/IEC specifies the dimensions and locations for each of the contacts on an integrated circuit card of an ID-1 card type. It also provides. ISO describes the physical characteristics of smart chip cards. It includes accommodation of exposure limits for electromagnetic phenomena such as. ISO is one of most important standards in the smart card industry. Parts of ISO specify physical characteristics, dimensions and location of the.
|Published (Last):||10 July 2004|
|PDF File Size:||20.67 Mb|
|ePub File Size:||19.40 Mb|
|Price:||Free* [*Free Regsitration Required]|
The RSC interface however defines two separate wires for data transmission and reception which would need hardware modification in order to interface with the single wire IC card directly.
It has to be said that this part of the standard could be improved and there is currently some work taking place in ISO on this very subject.
ISO part 2 smart card standard
Physical characteristics of a card includes: ETSI in the development of its standards has adopted a far more rigorous specification of 20mA maximum for normal use and a 10mA maximum for use in portable equipment. These commands cover the entire life cycle of the card and therefore some commands may be used before the card has been issued to the cardholder or after the card has expired.
One of the issues surrounding the use of the IC card relates to the temperature range for operational use. It includes the following:. The resistance of the card to static electricity is defined by a test set up as shown in figure 8. Cards with contacts — Physical characteristics”.
The principal parameters of ISO are the dimensions of the ID -1 card which are defined to be, This part specifies characteristics for a magnetic stripe, the encoding technique and coded character sets which are intended for machine reading. ISO Identification cards – Physical characteristics Related Posts Smart Card.
Created inupdated inamended 7816-22 The bending properties are tested by deflecting the card on each axis as shown in figure 6.
Both of these parameters have problems. The Part 1 standard also defines additional characteristics that should be met in the manufacturer of an IC card. The transmission protocol must take account of this need to turn the line around. For this purpose the back is defined to be the side with the magnetic stripe. Cards with contacts — USB electrical interface and operating procedures”.
From Wikipedia, the free encyclopedia. This ios often consists of a movable carriage that positions the card under the connector head while applying the necessary wiping and pressure action.
Newer chip fabrication technologies are moving sub micron, 0. Security operation commands are standardized by this criterion. The ISO standard includes specifications for the commands for card management. The first three parts in particular are well established and allow total physical and electrical interoperability as well as defining the communication protocol between the IC card and the CAD Card Acceptor Device.
Although the integrated circuit could contain its own clock circuit for driving the internal logic, in practice most IC chips are supplied with an external clock by the interface device. According to its abstract, it specifies a card application. Even jso embossing process itself is mechanically stressful and must raise serious doubts over the appropriate migration strategy. Data Layout on Magnetic Stripe Cards. Let us know what you have to say: Although the PC operates in full duplex mode.
A card may support either but not both simultaneously. Part iwo Location of magnetic read only tracks io tracks 1 and 2. The ISO standard 7816-22 meant for personal identification of the user. The physical properties of the contact IC card are referenced against earlier card standards and we will look at each of them in turn.
Cards with contacts — Dimensions and location of the contacts”. It should be noted that the thickness dimension does not include any allowance for embossing. The problems of uso start at the bottom, in other words with the physical dimensions of the card and the location of the contacts.
This standard in its many parts is probably the most important specification for the lower layers of the IC card. Unfortunately the French chip position overlaps the ISO magnetic stripe definition. The parity bit is defined to achieve even parity which means that the number of 1’s in the 8 data bits and the parity bit together results in an even number.
Commands for application management in a multi-application environment”. Return to page 1. These standards are well established so are the more important characteristics of a Smart Card which form the basis of the existing and emerging standards. The ISO family includes eleven parts which are in a constant state of flux as they are subject to revision and update.
Got Something To Say: Many observers have commented that the widespread use of Smart Cards is being impeded by the lack of standards. Technical Adviser to Smart Card News. In other iwo Wikimedia Commons.
Some of those industry standards are as follows:. Your email address will not be published. Cards with contacts — Electrical interface and transmission protocols”.